Runco CW-61 Instrukcja Użytkownika

OWNER’S OPERATING MANUAL CW-42i with Flat Panel Plasma Display

1 POWER Turns the plasma monitor’s power on and off. 2 REMOTE SENSOR WINDOW Receives the signals from the remote control.3 POWE

RGB1D-SUBDVIVIDEO123AUDIO 1L(MONO)RDVD1/HD1YCb/PbCr/PrAUDIO 2L(MONO)RDVD2/HD2RGB2RGYB Cb/PbHDVDAUDIO 3L(MONO)DVD3/HD3RGB3D-SUBEXTERNAL CONT

10» Plasma Remote ControlPart Names and Functions1 ON/OFF Switches Power ON/OFF. (This does not operate when POWER/STANDBY indicator of the main un

11OVERALL FUNCTIONAL DESCRIPTIONDIGITAL INPUTS:• DVD 1 / HD1This is a High Definition Digital input. Runco recommends using this digital input w

12INSTALLATIONVCR or Laser Disc PlayerVIDEO 1-3DVD Player To Mini D-Sub 15 pin connectoron the plasma monitorTo video inputs onthe plasma monitor IBM

» Connecting Your PC or Macintosh ComputerConnecting your PC or Macintosh computer to your plasma monitor will enable you to display your computer’s s

14Installation» Pin Assignments for 15-pin RGB (analog)» Pin Configuration of the RGB3 Connector (DVI Connector)The unit is equipped with a type of con

15BASIC OPERATIONS» POWERTo turn the unit ON and OFF:1. Plug the power cord into an active AC power outlet.2. Press the POWER ON button (on the remote

LTR BOX modeThe image in the Letterbox mode will be zoomed in, and the top and bottom portion ‘blanked off.’ This ratio is best suited for LaserDisc

17Aspect Ratio Controls» Wide Screen Operation with Computer SignalsSwitch to the wide screen mode to expand the 4:3 image to fill the entire screen.1.

» Menu OperationsThe OSD window is displayed with respect to the screen as shown on the diagram. * Depending on the screen’s mode, the OSD may be disp

19OSD (On Screen Display) ControlsMain Menu Sub Menu Functions Default ResetPICTURE ADJUSTCONTRAST Adjusts the contrast. Center YesBRIGHTNESS Adj

Main Menu Sub Menu Functions Default ResetRGB (VGA signals), VIDEO (Moving picture), WIDE (Wide VGA), DTV.HD TYPE Sets the digital broadcasting (1080A

OSD (On Screen Display) Controls» PICTURE ADJUST MenuAdjusting the picture The contrast, brightness, sharpness, color and tint can be adjusted as desi

Setting the picture mode according to the brightness of the roomThere are four picture modes that can be used effectively according to the environment

Reducing noise in the pictureUse these settings if the picture has noise due to poor reception or when playing video tapes on which the picture qualit

Setting the KELVINUse this procedure to set color tone produced by the plasma display. Example: Setting “6500K” Press the MENU button on the remote co

25Adjusting the Color to the Desired LevelUse this procedure to adjust the white balance for each color temperature to achieve the desired color quali

Changing the GAMMAThis feature adjusts the brightness of the midtone areas while keeping shadows and highlights unchanged.Example: Setting “2.8”Perfor

Adjusting the ColorsUse this procedure to adjust hue and color density for red, green, blue, yellow, magenta and cyan. Such adjustments will not affec

1TABLE OF CONTENTSIntroduction ... 2Important Information ...

» AUDIO MenuAdjusting the treble, bass and left/right balance and audio input select The treble, bass and left/right balance can be adjusted to suit y

OSD (On Screen Display) ControlsSetting the allocation of the audio connectorsSetting the AUDIO 1, 2, and 3 connectors to the desired input. Example:

» IMAGE OPTIONS MenuThe position of the image can be adjusted and flickering of the image can be corrected. Example: Adjusting the vertical position in

Information When “COMPUTER” is offWhen Auto Picture is off, the Fine Picture and the Picture ADJ. items area displayed so that you can adjust them.

» INSTALL 1 MenuSetting the on-screen menuThis sets the position of the menu, the display format (horizontal or vertical) etc. Example: Turning the DI

33OSD (On Screen Display) ControlsSetting the BNC connectorsSelect whether to set the input of the 5 BNC connectors to RGB and Component.Example: Set

Checking the signal being transmitted to RGB1 terminalUse this to confirm the signal being transmitted to the RGB1 terminal. It is set to RGB and can n

35Setting high definition images to the suitable screen sizeUse this procedure to set whether the number of vertical lines of the input high definition

Setting the Input SkipWhen this is ON, signals which are not present will be skipped over and only pictures whose signals are being transmitted will b

37OSD (On Screen Display) ControlsResetting to the default valuesUse these operations to restore all the settings (PICTURE ADJUST, AUDIO, IMAGE OPTION

2INTRODUCTION» Introduction to the Runco CinemaWall™ CW-42i Flat Panel Display MonitorThe CW-42i is a state-of-the-art, DTV-compatible, flat-panel pl

» INSTALL 2 MenuSetting the Auto Off for computer imagesThis energy-saving (Auto Off) function automatically reduces the monitor’s power consumption i

39OSD (On Screen Display) ControlsPOWER / STANDBY indicatorAUTOOFFmodePOWER / STANDBY indicatorAUTO OFF operating statusDescription Turning the pictur

40OSD (On Screen Display) ControlsPlasma Display Panel Protection (PDP PROTECT)Reducing burn-in of the screenThe brightness of the screen, the positio

ORBITERUse this to set the picture shift.Example: Setting ”ORBITER” to “AUTO1”Perform Steps 1-2 of PDP PROTECT, then...3. Use the and buttons to s

42OSD (On Screen Display) ControlsINVERSEUse this to set the inverse mode or to display a white screen.Example: Setting “INVERSE” to “WHITE” Perform S

43OSD (On Screen Display) ControlsIMAGE SWEEPWhen this is set to ON, a white vertical bar moves repeatedly from the left and of the screen to the righ

SOFTENReduces edges and softens the image.Example: Setting “SOFTEN” to “2”3. Use the and buttons to select “SOFTEN”.4. Use the and button to s

Setting the screen size for S1/S2 video inputIf the S-Video signal contains screen size information, the image will be automatically adjusted to fit t

» INSTALL 3 MenuUsing the timerThis function sets the monitor to turn ON/OFF automatically at a set time.Perform the following operations.1. On the MA

47OSD (On Screen Display) ControlsThe mode switches as follows each time the or buttons is pressed:• DAYLIGHT SAVING TIME ON OFF• DAY SUNDAY

IMPORTANT INFORMATION3» PrecautionsPlease read this manual carefully before using your plasma monitor and keep the manual handy for future reference.

48Setting the DEFAULT INPUTThis function sets the input mode at the time the power is switched on. Example: Setting “VIDEO2” Perform the following ope

49Enabling/disabling the front panel controlsThis function enables/disables the front panel controls. Example: Setting “ON” Perform the following oper

Enabling/disabling remote control wireless transmissionThis function enables/disables remote control wireless transmission.Example: Setting “OFF”Perfo

ID Number SettingWhen using more than one of these displays, this function sets ID numbers so that operation of the remote control does not cause mult

52OSD (On Screen Display) ControlsVideo Wall SettingUse this feature to configure a 2×2 or 3×3 video wall. Perform the following operations.Press the M

DIVIDERSet the 2x2 or 3x3 video wall.Example: Setting “4”Perform Steps 1-2 of VIDEO WALL, then...3. Use the and buttons to select “DIVIDER”.4. Use

DISP. MODESelect the screen mode from between two options (Splitting, Blanking).Example: Setting “BLANK”Perform Steps 1-2 of VIDEO WALL, then...3. Use

IMAGE ADJUSTThe position of the image can be adjusted and flickering of the image can be corrected.Example: Adjusting the vertical position.Perform Ste

56OSD (On Screen Display) ControlsLUM SET LINKUse this function to set a uniform brightness for each display.Turn on the AUTO ID before the following

57OSD (On Screen Display) ControlsREPEAT TIME (REPEAT)Use this to set two timers. Each timer can use the DIVIDER, SOURCE and ACTIVE functions.Turn on

Important InformationNOTE:When you connect a computer to this monitor, use an RGB cable including the ferrite core on both ends of the cable. And rega

58OSD (On Screen Display) Controls» LANGUAGE MenuSetting the language for the menusThe menu display can be set to one of seven languages: English, Ger

59OSD (On Screen Display) Controls» COLOR SYSTEM MenuSetting the video signal formatUse these operations to set the video standards of composite video

60OSD (On Screen Display) Controls» SIGNAL INFO. MenuChecking the frequencies, polarities of input signals, and resolution Use this function to check

61TABLE OF SIGNALS SUPPORTEDModel[ Signal Type ]Dots x LinesVerticalFreq.(Hz)HorizontalFreq.(kHz)Sync Polarity Presence Screen ModeRGBSelect *5DVIMem-

62Table of Signals Supported (continued)Model[ Signal Type ]Dots x LinesVerticalFreq.(Hz)HorizontalFreq.(kHz)Sync Polarity Presence Screen ModeRGBSele

TROUBLESHOOTINGSYMPTOM CHECKS REMEDYPicture is disturbed. Sound is noisy. Remote control operates erroneously.• Is a connected component set directly

64DIMENSIONS41.25025.6253.87542" diagonal

SPECIFICATIONS65Native Resolution:853 x 480Screen Size:42 in. (diagonal)Screen Aspect Ratio:16:9Available Aspect Ratios:4:3, Letterbox, 16:9 Anamorphi

5LIMITED WARRANTYCongratulations on your purchase of a Runco International video product and welcome to the Runco family! We believe Runco produces “T

RUMA-01040001-17-06 v2.0Runco International2900 Faber StreetUnion City, CA 94587Ph (510) 324-7777 / Fax (510) 324-93001-800-23RUNCO

Limited Warranty6CAUTION: THIS LIMITED WARRANTY ONLY COVERS RUNCO PRODUCTS PURCHASED FROM RUNCO AUTHORIZED DEALERS. ALL OTHER PRODUCTS ARE

7HOW TO ATTACH OPTIONS TO THE PLASMA MONITORYou can attach your optional mounts or stand to the plasma monitor in one of the following two ways: 1) Wh